Acceleration, Force And Mass Essay, Research Paper
Aim: ?I intend to
investigate the rule of F = M*A and so investigate the relationships
between acceleration, force and mass and how they affect each other.Preliminary Workings: The main aim of my project is to investigate three factors,
and so I will start off with a few lines about each of them. The idea of a force is
fundamental to physics and it is simply thought of as a push or a pull, but
this is not satisfactory for my purposes. We cannot see a force but instead we
can see its effect on an object (the principle of Brownian Motion), so forces
are described in terms of what they do. Forces tend to cause changes in an
objects 1.
Shape or size 2.
Speed in a straight line 3.
Direction Forces are measured in newtons (N), named after the person
who first invented this unit. When several forces act on an object, they can
either combine to give an overall force ? which will change the object?s shape
or motion ? or they could cancel each other out, giving no overall force. In
the last case it could be said that the forces are ?balanced?. If there is no
force acting, or if all the forces acting on an object are balanced, then there
will be no change taking place. An object at rest will remain at rest, and a
moving object will continue to move, keeping the same speed and travelling in
the same direction. ??????????? The mass
of an object tells us how much matter it contains and is measured in the unit
of kilograms (kg). Whereas mass is a scalar quantity (magnitude only), forces
are vector quantities, meaning they have both direction and magnitude. ??????????? Acceleration
is the rate at which the velocity of an object changes, over a period of
time. It is measured in metres-per-second per second (m/s/s) or
meters-per-second squared (m/s²), and it tells you how much the velocity will
change each second. The acceleration of an object can be calculated by using
the following formula:(average) acceleration (m/s²) =?? change in velocity (m/s)??????? or in symbols: a = v – u ??????????????????????????????????????????????? ? time taken for the change (s)?? ??????????????????????????????????? twhere u is the velocity at the beginning of the time
interval and v is the velocity at the end of the time interval. When an
object is slowing down the change in the velocity is negative (because v is
less than u), and so the acceleration is negative. This is sometime
called deceleration. The acceleration at any point on a? journey can be calculated by measuring the
slope of a velocity-time graph. In effect this is the same as applying the
formula that I have included above. To show some of these graphs I have
included some below to show how different accelerations can be portrayed for
varying and constant changes.??????????????????????????????????? Velocity (m/s)?????????????????????????????????????????? Velocity (m/s) ??????????? ?????????????????????????????????????????????????? Time (s)???????????????????????????????????????????????????????? Time (s) ??????? Steady
acceleration from rest???????????????????
Increasing acceleration from rest From these examples it is possible to work out what other
graphs of this type would look like and should stand me in good stead for this
project.The next scientific that I will look at is that worked on by
the famous scientist that I have already mentioned ? Sir Isaac Newton. During
his work he discovered some laws of motion, which are quite appropriate to what
I am investigating: Law 1: Any object will continue to do what it is
already doing unless a resultant force is acting on it.?????? I am used to the idea that an object on the ground, which is
given to start it, will come to rest quickly. Of course once it is moving,
friction is a force that acts upon it to cause a change, in this case a
reduction in velocity until the object stops. Without friction, as in space, an
object given a push will continue to move in a straight line with the velocity
it had at the end of the push. This can be showed using an air track or some
other method of reducing friction. Though the law refers to a resultant force.
So the other way in which an object can remain in a constant state is if the
resultant force acting on it is zero. Law 2: Constant acceleration causes
constant acceleration. The greater the force, the greater the acceleration for
that particular body. Therefore force is proportional to acceleration.? F??????
a If a particular acceleration is to be achieved, the force
required to achieve it is also dependant on the mass to be moved. So? F??????
m??????????? ??????????? Then F = ma If we define the unit of force such that 1 unit of force
will accelerate 1kg by 1 m/s² we have the definition of the Newton. This can
also be thought of by another means. The formula can be arranged to read that m
= F/a so that the bigger the mass the less the acceleration that could be
produced. One-way of thinking about mass is to regard it as the ?lack of
willingness to move? of an object. This property is sometimes called inertia.
The F in the equation is the resultant force acting on an object.Law 3: When an object is acted on by a force, then
somewhere another object is acted on by an equal force in the opposite
direction. This research has made me think about exactly how I am to
carry out this experiment. I feel that I have researched enough evidence but
now it is time for me to consider the method from which I will take my results
and with that my conclusions and evaluations. Firstly I will need to measure
the acceleration of an object and there is an instrument available to me that
can perform this task very well indeed. That is a ticker-timer. A piece of
ticker-timer tape is passed through the instrument and as an object moves along
(with one end of the tape attached) it is pulled through the ticker-timer. A
vibrating beam marks points on a piece of carbon paper and this in turn marks
along the tape and it does this at a rate of 200 dots per second. By taking a
sequence of these dots (for this experiment I will use 10) the acceleration of
the object can be determined. Therefore if the dots are equally spaced then the
acceleration is constant and if the spacing between the dots increases each
time, the acceleration is becoming greater. The next step is to use the formula
distance = speed * time to work out the velocity of the first ten dots
(from rest). The velocity is then taken for the next ten dots and the
acceleration between these two times is calculated. The formula for
acceleration, as previously stated is:(average) acceleration (m/s²) =?? change in velocity (m/s)??????? or in symbols: a = v – u ??????????????????????????????????????????????? ? time taken for the change (s)The time taken in this equation is that for ten dots and
this equates to a time period of 0.2 seconds.Preliminary Experiment and Method: ? Before any experiment is taken out, there should always be
an experimental trial to determine factors such as ranges and to make
alterations to the overall set-up to gather the most accurate data that is
possible. Firstly I have already stated what I hope to achieve, but little in
the way that it will actually be carried out. The formula of F = ma will
be applied to a wooden trolley, which will have its mass recorded before the
experiment, and have its acceleration measured throughout. A range of masses
(acting as the force for my purposes) will be attached to the front end of the
trolley by way of a pulley system (shown in my diagram) and attached to the other
end will be a piece of ticker-timer tape on which will generally record the
acceleration. The ticker-timer will be turned on and then the force will be
allowed to pull the trolley from its rest position while its acceleration is
recorded by way of the dots marked on the ticker-timer tape. When the trolley
has reached the end of its course the results will then be recorded. As I have
previously stated a preliminary test was done before final readings were taken
and here are the results: Mass /kg
(trolley) Force /N (force applied) Distance1 /m Velocity1 /m/s Distance2 /m Velocity2 /m/s Acceleration /m/s² 0.302 0.5 0.018 0.090 0.032 0.160 0.350 0.302 1.0 0.031 0.150 0.066 0.330 0.900 0.302 2.5 0.063 0.315 0.147 0.735 2.100 0.302 3.0 0.077 0.385 0.173 0.865 2.400 0.302 4.5 0.093 0.465 0.215 1.075 3.050 ? I was pleased with what I managed to take out from my
preliminary experiment. The ranges used for the results above are those that I
will use for the final experiment. This is for a number of reasons. Firstly,
metal weights are being used as the acting force and the smallest one that is
available to me is 50g which equates to 0.5N, and so this is the lower group
boundary. As for the upper boundary the value that I have chosen is 4.5N as the
next value above available to me, 5N, caused the trolley to accelerate at such
a rate that by the time it reached the end of the course, and the weights had
reached the ground, 20 marks had not been made on the ticker-timer paper and so
proper analysis could not be undertaken ( a fair test would not be maintained).Fair Test: A fair test must be ensured at all times, in any experiment,
to keep the results as accurate as possible so that appropriate conclusions can
be drawn. The main way that I hope to achieve this is by repeating each of my
results a further two times so that an average can be taken and any anomalous
results can be spotted before they are taken as genuine ones. As well as this I
must consider how accurate I want my results to be. As seen above I
think that giving my results to 3 decimal places would be appropriate as this
allows good continuity and does not suffer from premature approximation.
Another point that I will uphold is to use the same pieces of equipment for
every different interval. Should the experiments take more than one lesson then
I will mark each individual piece so I can recognise it at a later date.
Another point is the set-up must be the same for both experiments, if this does
not happen then I would not expect very accurate results at all. To make sure
that my results are accurate I will only change one factor at a time. In fact
there is only one factor that will be changed during the whole experiment. Factors To
Change Factors To Fix Factors to
Measure 1.The force being applied on the trolley (the total
amount of weights on the pulley system). Measured in Newtons. 1.The mass of the trolley, acting as the mass in
the formula F = ma. Measured in grams. 1. The acceleration of the trolley over the course.
Measured in metres /second². 2. The velocity of the trolley over the course. Measured
in metres / second. 3. The two different distances (see diagram). Measured in
centimetres. ? Safety Precautions: On the surface this is not a highly dangerous experiment,
however what must be shown is awareness of the environment that it is taking
place in. There will be many groups working within a very small area and this
means that conflicts can arise over space and working conditions. As well as
this the pull system will be dropping the weights into an aisle where other
groups of people will be walking. Therefore everyone will have to be vigilant
as to where they are walking. Other then this something soft will be placed
between the ground and where the weights will land. Plus the apparatus will be
kept securely on the bench so it is not knocked off with the clamp the clamp
being securely fixed. Hypothesis: Through my preliminary workings, and my initial scientific
research, I have begun to understand what I think my final results will show. Firstly my investigation is based around the formula of? F = ma. In the set-up that I am using
the only factor that is constant is the mass (the trolley). From this you can
tell something about the proportionality between the other two factors, the
force and the acceleration. That is that they are proportional, and this
is stated in Newton?s laws of motion. You can tell? proportionality on a graph because of two features: 1.The graph is a straight line ???????????????? 2. The line goes straight through the origin We
also know that when the graph has been drawn we will be able to take the
gradient of the line. This gradient should be equal to mass of the trolley:F = kak = F / a ??????? ??? ??????????? (k is an unknown constant, in this case the mass of ?the trolley or the gradient) If we were to keep the same force acting on the trolley, but
to change the mass each? time, this is
what we might expect.??????????????????????? m
= F / a ???????? ;?????????? m = k / a????????? ;?????????? m???
1 / aThis tells you that the mass of the trolley will be
proportional to inversion of the acceleration (1 / a). Yet again the graph of
this will be a straight line through the origin. From this, if you took the
gradient of the graph mass against 1 / acceleration then the
gradient will be the 1 / Force acting on the trolley. Here is how we know
this:??????????? m??? 1 / a ????????? ;
????????? gradient? =??????? 1
/ a??? = ????????? 1 / F ???????????????????????????????????????????? ?????????????? ??????????? ??m Overall I state that when Force is plotted against acceleration
then the graph will be directly proportional. Then if I take the gradient of
the graph then it should equal the mass of the trolley. On the other hand I
will only be able to speculate from my results what will happen when the force
is remaining constant as it will not be possible to have a range of masses to
do the experiment with, and the force is what I have stated I am changing each
time!Results: Mass /kg (trolley) Force /N (force applied) Distance 1 ????? /m Velocity1 /m/s Distance 2 ?/m Velocity2 /m/s Acceleration /m/s² Average Acceleration /m/s² 0.775 0.5 0.021 0.022 0.021 0.105 0.110 0.105 0.034 0.036 0.034 0.170 0.180 0.170 0.325 0.350 0.325 0.333 0.775 1.0 0.031 0.033 0.032 0.155 0.165 0.160 0.062 0.065 0.063 0.310 0.325 0.315 0.775 0.800 0.775 0.783 0.775 1.5 0.041 0.043 0.045 0.205 0.215 0.225 0.082 0.082 0.080 0.410 0.405 0.400 1.025 0.950 0.875 0.950 0.775 2.0 0.056 0.058 0.055 0.280 0.290 0.245 0.112 0.114 0.113 0.560 0.580 0.565 1.400 1.450 1.450 1.433 0.775 2.5 0.064 0.064 0.063 0.320 0.320 0.315 0.120 0.125 0.123 0.600 0.625 0.615 1.400 1.525 1.500 1.475 0.775 3.0 0.072 0.071 0.070 0.360 0.355 0.350 0.144 0.141 0.140 0.720 0.705 0.700 1.800 1.750 1.750 1.766 0.775 3.5 0.077 0.078 0.080 0.385 0.390 0.400 0.156 0.152 0.155 0.790 0.760 0.775 1.975 1.850 1.875 1.900 0.775 4.0 0.071 0.072 0.074 0.355 0.360 0.370 0.165 0.164 0.164 0.825 0.820 0.820 2.350 2.300 2.250 2.300 0.775 4.5 0.062 0.067 0.065 0.310 0.335 0.325 0.174 0.177 0.178 0.870 0.885 0.890 2.800 2.775 2.825 2.800 ??????????? ? Graph Analysis: Through my working I have been able to draw a graph of Force
against acceleration for which, as I have previously stated, the
gradient would be the mass. Although this is not exactly what I determined,
which I will come to later, I did find my initial hypothesis to be correct;
that is that as the force being applied to the mass (trolley) increases then
the subsequent acceleration of the mass (trolley) would also increase. However
there is more to it than that and so I will analyse all of my graphs more
closely. Graph A is a graph to show the average results for Force against
acceleration. The main point that I have focused on so far is that when
this graph is plotted, because of its direct relation to the formula ?F = ma, the graph shows the following
m = F / a. This means that when the gradient of the straight line is
taken (for this is a graph of proportionality) the gradient will equal the mass
in the formula (the trolley). I, indeed, did measure the gradient of the graph
(which should have been 0.775 ? 0.775g) and it did not equal the mass. In fact
with a measurement of 1.5, it is considerably far away, and if I were to take
it on face value then this would mean that the trolley weighed 1.5kg! Alarmed
at this I decided to draw another graph, which would show the results that I
had expected, and it was indeed quite different. There must be another force
acting that I have so far ignored, and yes there is. That force is friction,
which I have only briefly mentioned before in my preliminary work. Friction is
a force that opposes the movement of an object, and it acts in the opposite
direction to the way the object is moving. Between two surfaces it depends
on? a. the type of surface b .the
size of the reaction force. From these facts I can begin to understand why my
graph looks the way it does. Also, if looked at closely, the line of the
results does not go through the origin of the graph. This tells me that, just